번역


+86-371-67829333

소식

Ways of Cable Laying

What should I pay attention to when laying directly? Under what circumstances is it used? For direct buried laying, it is necessary to consider whether the cable is easily damaged by external impact.

If it will not be subjected to a large impact, direct laying is possible. If it may be subjected to some relatively large impacts, but the strength can be controlled within a certain range, direct burial of armor can be considered. If the external force is larger, a protective casing needs to be used, which can be set locally (such as through the road).

Advantages and Disadvantages of Direct Burial of Cables

Advantages: easy to lay, save materials and labor.

Disadvantages: maintenance is inconvenient. If maintenance is required, the covering soil needs to be excavated. It is only recommended for use in places where maintenance is not considered or can be accepted. When buried directly, it is generally necessary to pad with yellow sand.

Cable wells may not be provided for cables with 6 or less cables, and there are many wells for cables, which is convenient for replacement and addition of cables. There is no need to set up a cable well when the municipal 10KV cable enters the factory area, it can be directly buried from the terminal rod to the 고전압 power distribution cabinet.

The unit builds a new factory building, and the construction transformer and high-voltage lines are far from the construction center. Since it is a steel structure factory building, overhead lines cannot be used to avoid conflicts with the steel structure installation. 이것 low-voltage cable is directly buried.

About Laying Pipes

Compared with direct burial, cable laying through pipes is more convenient for later maintenance and additional lines. For cables laid through pipes, some spare pipes can be considered to prepare for future line maintenance and capacity expansion.

When laying through pipes, it is necessary to consider setting up cable wells when the turning angle of the line is large or the distance of the straight section is long. When the number of cables is small and the wire diameter is small, the cable hand well can be used. In the case of more cables and larger diameters, it is necessary to consider setting up cable manholes. The cable well can be done according to the Atlas practice. In addition to the atlas method, many small passage wells can also be directly bricked or poured with concrete. 이때, it is necessary to consider setting water seepage holes at the bottom.

Pipe laying is mainly used in areas with many lines and concentrated routes. Relatively speaking, it is more convenient to lay down pipes and save materials.

If there is an external line in a factory area, there are more than a dozen low-voltage and strong-current cables, and there are also weak-current (TV, telephone, network) 케이블, and there are more than 8 strong-current cables. Try not to line up together, and try to set the strong and weak electric tubes on both sides of the road when doing municipal work.

About Laying the Cable Trench

Attention should be paid to the laying of cable trenches. Cables of different voltage levels should be arranged in different brackets, and drainage measures should be taken into account in the cable trench itself. And consider measures to prevent small animals such as mice from entering.

게다가, it mainly depends on factors such as engineering conditions, environmental characteristics, and the number of cable types, as well as the selection to meet the requirements of reliable operation, 쉬운 유지 보수, and technical and economical rationality. It is uncertain whether there are mandatory index requirements.

The depth of the cable trench is determined according to the number of cables and the number of cable types. 예를 들어, there are control cables, low-voltage power cables, 및 고전압 전원 케이블. 일반적으로, three layers are set up, and the spacing between each layer is generally 250~300. This determines the height.

ZMS Cable F

Recent Posts

유럽의 의료용 광섬유 시장에 대한 강력한 수요 추세

유럽의 의료 산업은 최근 몇 년 동안 상당한 발전을 이루었습니다., driven by the integration

3 weeks ago

로켓 발사에 처음부터 끝까지 어떤 산업 케이블이 사용됩니까??

로켓의 성공적인 발사에는 상상할 수 있는 가장 복잡한 엔지니어링 업적 중 하나가 포함됩니다.,…

1 month ago

광섬유 케이블을 생산하는 데 어떤 광섬유 재료가 사용됩니까??

광섬유 케이블은 현대 통신의 중추가 되었습니다., offering high-speed data transmission over

1 month ago

일반적으로 고전압 구리 케이블의 코어 수는 몇 개입니까?? 응용 프로그램은 무엇입니까?

고전압 구리 케이블은 전력 분배 및 전송에 필수적인 구성 요소입니다.,…

2 months ago

철도 시스템에 사용되는 고전압 선은 무엇입니까?

Railroad high voltage lines play a vital role in powering the railway systems that transport

3 months ago

단일 모드와 다중 모드 광섬유 케이블의 차이점은 무엇입니까?

광섬유 케이블은 현대 통신 네트워크의 중요한 구성 요소입니다., enabling high-speed data transmission over

3 months ago